基于非线性Drive-shaft模型的车辆传动系统冲击响应

建立了包含线性与非线性项的车辆传动系统非线性Drive-shaft模型, 应用具有耗散项的拉格朗日方程将非线性Drive-shaft模型转换为当量化的两质量模型, 通过将两端扭转角等效到同一端获得了传动系统的冲击响应方程, 应用Routh-Hurwitz准则分析了冲击响应方程的稳定性, 获得了稳定性参数区间。仿真结果表明: 将非线性阻尼分别设置为0和线性阻尼的1/10、-1/10时, 冲击响应首个峰值的绝对值分别为0.153 9、0.101 4、0.371 6, 当非线性阻尼为线性阻尼的1/10时, 冲击响应的首个峰值的绝对值最小, 这说明正的非线性阻尼有利于冲击响应的衰减; 将非线性刚度分别设置为0和线性刚度的1/10、-1/10时, 获得的冲击响应首个峰值的绝对值分别为0.153 9、0.178 8、0.115 9, 当非线性刚度为线性刚度的-1/10时, 冲击响应的首个峰值的绝对值最小, 这说明负的三次方非线性刚度有利于冲击响应的衰减; 在固定非线性刚度为线性刚度的-1/10的基础上, 将代表非线性阻尼的系数分别设置为0.1、0、-0.1, 获得的冲击响应首个峰值的绝对值分别为0.078 4、0.114 2、0.231 6。可见, 当代表非线性阻尼的系数设置为0.1时, 冲击响应的首个峰值的绝对值最小, 这表明在传动系统线性刚度及线性阻尼的基础上, 设计负的非线性刚度及正的非线性阻尼可以提升传动系统抵抗冲击的性能。      

S^2 BHCA Multiple AUVs cooperation oriented control architecture

Oceanographic survey, or other similar applications should be the applications of multiple AUVs. In this paper, the skill ＆ simulation based hybrid control architecture （S^2BHCA） as the controller＇s design reference was proposed. It is a multi-robot cooperation oriented intelligent control architecture based on hybrid ideas. The S^2BHCA attempts to incorporate the virtues of the reactive controller and of the deliberative controller by introducing the concept of the ＂skill＂. The additional online task simulation ability for cooperation is supported, too. As an application, a multiple AUV control system was developed with three ＂skills＂ for the MCM mission including two different cooperative tasks. The simulation and the sea trials show that simple task expression, fast reaction and better cooperation support can be achieved by realizing the AUV controller based on the S^2BHCA.     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

曲线钢轨抗磨耗损伤技术的应用

文章结合永安—漳平段线路钢轨现状调查,建立了抗磨损研究试验段,通过对试验结果分析,总结出减少钢轨鱼鳞损伤,以及机车轮缘磨耗的措施,为线路钢轨养护提供借鉴经验。     

Experimental study on the width of the turbulent area around bridge pier

At present, the method of calculating the turbulent flow width around the bridge pier is not given in the "Standard for Inland River Navigation" (GB50139-2004) in China, and the bridge designer usually increases the bridge span in order to ensure the navigation safety, which increases both of the structural design difficulty and the project investments. Therefore, it is extremely essential to give a research on the turbulent flow width around the bridge pier. Through the experiments of the fixed bed and the mobile bed, the factors influencing the turbulent flow width around the bridge pier have been analyzed, such as the approaching flow speed, the water depth, the angles between the bridge pier and the flow direction, the sizes of bridge pier, the shapes of the bridge pier, and the scouring around the bridge pier, etc. Through applying the dimension analytic method to the measured data, the formula of calculating the turbulent flow width around the bridge pier is then inferred.     

复合励磁同步发电机的Matlab建模与仿真

通过对Matlab/Simulink中同步电机的内核模型进行改造,建立了双输出绕组的复合励磁同步发电机模型,并对单输出绕组的复合励磁同步发电机的励磁调节特性进行了仿真,仿真结果说明:本文提出的方法简捷有效.     

地铁列车中可燃物热释放速率的测定

介绍了目前常用的室内火灾模拟方法——区域模拟与场模拟,并对其各自的特点和局限性进行对比讨论;同时还介绍了基于质量损失速率的热释放速率测试方法,给出了部分实验数据和结果分析。火源热释放速率的大小对于火灾的温度分布及烟气流动的影响较大。     

Mixed analysis of shell and solid elements using the overlaying mesh method

 This article presents a mixed method of analyzing shell elements and solid elements using the overlaying mesh method. In the structural design of a ship's hull, the shell elements are used for the global model. However, the solid elements are necessary to analyze the stress concentration zones or the vicinity of a crack. In such cases, the models are analyzed using zooming analysis, in which the results of a global model analysis are transferred to a local model analysis by imposing boundary conditions. This method is more advantageous than zooming analysis in terms of the accuracy of the solution and the modeling flexibility. Some examples of a plate model with a cracked surface or with a projection are shown in order to demonstrate the effectiveness of the method. Received: August 6, 2002 / Accepted: November 25, 2002 Address correspondence to: S. Nakasumi (sumi@nasl.t.u-tokyo.ac.jp) Updated from the Japanese original, which won the 2002 SNAJ prize (J Soc Nav Archit Jpn 2001;189:219–224; and 190:655–662)     

IN SITU EXPRESSION OF THE CELL ADHESION MOLECULE IN GASTRIC CARCINOMA AND CHRONIC GASTRITIS

ＩＮＳＩＴＵＥＸＰＲＥＳＳＩＯＮＯＦＴＨＥＣＥＬＬＡＤＨＥＳＩＯＮＭＯＬＥＣＵＬＥＩＮＧＡＳＴＲＩＣＣＡＲＣＩＮＯＭＡＡＮＤＣＨＲＯＮＩＣＧＡＳＴＲＩＴＩＳＣｈｅｎＧａｏｐｉｎｇ（陈高平）；ＬｉｕＹｏｎｇ（刘勇）；ＲｅｎＨｕｉｍｉ（任惠民）；ＬｉＨｅ...